Incorporated changes for release 1.3.0

RPiSetup/ap-setup.sh

@@ -0,0 +1,108 @@
+#!/bin/bash
+# Wireless Access Point Raspberry Pi Setup
+current_user=`whoami`
+if [ "$current_user" != "root" ]
+then
+	echo "You must have root privileges to run this setup."
+	echo "Try 'sudo ./ap-setup.sh'"
+	exit 1
+fi
+echo ""
+echo ""
+echo "If this terminal connects to a network using ethernet, it can be configured"
+echo "as a wireless access point for other terminals. Would you like to configure"
+echo -n "this terminal as an access point? [y/N]: "
+read wapconf
+if [ "$wapconf" = "Y" -o "$wapconf" = "y" ]
+then
+	echo "Configuring as wireless access point."
+	echo ""
+	echo "Copying files..."
+	chmod +x apsetup/usr/local/bin/*
+	cp apsetup/usr/local/bin/* /usr/local/bin
+	cp -R apsetup/etc/* /etc
+	echo ""
+	wapssidok=0
+	while [ "$wapssidok" -ne 1 ]
+	do
+		echo "This access point will need an SSID. This is what will appear"
+		echo "as the name of this terminal when other devices connect."
+		echo -n "Please enter the desired SSID for this access point:  "
+		read wapssid
+		if [ "$wapssid" = "" ]
+		then
+			echo "SSID cannot be blank. Try again."
+		else
+			wapssidok=1
+		fi
+	done
+	wappassok=0
+	while [ "$wappassok" -ne 1 ]
+	do
+		echo "You will need to set a passphrase for this access point. It should"
+		echo "be at least 8 characters in length and cannot be blank."
+		echo -n "Please enter the desired passphrase for this access point:  "
+		read wappass
+		wappasslen=`echo -n $wappass | wc -m`
+		if [ "$wappass" = "" -o "$wappasslen" -lt 8 ]
+		then
+			echo "Passphrase doesn't satisfy requirements above. Try again."
+		else
+			wappassok=1
+		fi
+	done
+	apt install hostapd
+	systemctl unmask hostapd
+	systemctl enable hostapd
+	echo "[NetDev]" >/etc/systemd/network/bridge-br0.netdev
+	echo "Name=br0" >>/etc/systemd/network/bridge-br0.netdev
+	echo "Kind=bridge" >>/etc/systemd/network/bridge-br0.netdev
+	echo "[Match]" >/etc/systemd/network/br0-member-eth0.network
+	echo "Name=eth0" >>/etc/systemd/network/br0-member-eth0.network
+	echo "" >>/etc/systemd/network/br0-member-eth0.network
+	echo "[Network]" >>/etc/systemd/network/br0-member-eth0.network
+	echo "Bridge=br0" >>/etc/systemd/network/br0-member-eth0.network
+	systemctl enable systemd-networkd
+	mv /etc/dhcpcd.conf /etc/dhcpcd.conf.old
+	echo "denyinterfaces wlan0 eth0" >/etc/dhcpcd.conf
+	cat /etc/dhcpcd.conf.old >>/etc/dhcpcd.conf
+	echo "interface br0" >>/etc/dhcpcd.conf
+	rfkill unblock wlan
+	echo "country_code=US" >/etc/hostapd/hostapd.conf
+	echo "interface=wlan0" >>/etc/hostapd/hostapd.conf
+	echo "bridge=br0" >>/etc/hostapd/hostapd.conf
+	echo "ssid=$wapssid" >>/etc/hostapd/hostapd.conf
+	echo "hw_mode=g" >>/etc/hostapd/hostapd.conf
+	echo "channel=7" >>/etc/hostapd/hostapd.conf
+	echo "macaddr_acl=0" >>/etc/hostapd/hostapd.conf
+	echo "auth_algs=1" >>/etc/hostapd/hostapd.conf
+	echo "ignore_broadcast_ssid=0" >>/etc/hostapd/hostapd.conf
+	echo "wpa=2" >>/etc/hostapd/hostapd.conf
+	echo "wpa_passphrase=$wappass" >>/etc/hostapd/hostapd.conf
+	echo "wpa_key_mgmt=WPA-PSK" >>/etc/hostapd/hostapd.conf
+	echo "wpa_pairwise=TKIP" >>/etc/hostapd/hostapd.conf
+	echo "rsn_pairwise=CCMP" >>/etc/hostapd/hostapd.conf
+	wget -c http://github.com/pjz/webmin-modules/releases/download/v1.0/hostap.wbm.gz
+	gzip -d hostap.wbm.gz
+	/usr/share/webmin/install-module.pl hostap.wbm
+	echo ""
+	echo ""
+	echo "Wireless access point setup is complete. It will be"
+	echo "automatically enabled after reboot. To change the SSID or"
+	echo "passphrase in the future, edit the file /etc/hostapd/hostapd.conf"
+	echo "or use the Host AP module in the Servers section of Webmin."
+	echo ""
+	echo "To disable the access point altogether in the future, run:"
+	echo "	sudo wap-disable"
+	echo "at a command prompt and reboot the terminal. To re-enable it, run:"
+	echo "	sudo wap-enable"
+	echo "at a command prompt and reboot the terminal."
+	echo "It can also be enabled or disabled via Custom Commands in the Tools"
+	echo "section of Webmin."
+	echo ""
+	echo -n "Press enter key to continue..."
+	read cont
+else
+	exit 2
+fi
+